- 2000 Gmc Sonoma Transmission
- 99 Gmc Sonoma Manual Transmission Removal
- 2002 Gmc Sonoma Manual
- 99 Gmc Sonoma Manual Transmission Removal Diagram
Major service of your Chevrolet Blazer transmission requires careful planning and organization. Make sure you have an adequate place to work safely and with plenty of time. Besides having the right. RARE LOW MILESoriginal owner family GMC Sonoma S15 Extended Cab Truck, a rare find and a dependable daily driver. The truck has been garaged since new. All regularly scheduled maintenance performed. The manual transmission and clutch are employed to vary the relationship between engine. Remove the extension housing seal using Removal Tool T74P-77248.
Service Manual
Manual Transmission Disassembly and Reassembly
View
1.Clutch Housing Exploded View
Exploded View - Clutch Housing
2.Transmission Housing Exploded View
2000 Gmc Sonoma Transmission
Exploded View - Transmission Housing
Disassembly
NOTE: Place the clutch housing on two pieces of wood thick enough to keep the mainshaft from hitting the workbench- 1.M/T Change Lever Assembly
1- Remove the change lever assembly (A)- 2- Remove the 8 x 10 mm dowel pins (B)- 2.Back Up Light Switch
1- Remove the back-up light switch (A) and the 18 mm sealing washer (B)- 3.M/T Output Shaft Speed Sensor
1- Remove the output shaft (countershaft) speed sensor (A), the plain washer (B), and the O-ring (C)- 4.M/T Transmission Housing Assembly
1- Remove the detent bolts (A), the 12 mm sealing washers (B), the detent ball springs (C), and the steel balls (D)- 2- Remove the 20 mm bolt (E) and the 20 mm sealing washer (F)-
3- Remove the drain plug (A) and the sealing washer (B)- 4- Remove the filler plug (C) and the sealing washer (D)-
5- Remove the 8 mm flange bolts in a crisscross pattern in several steps-
6- Remove the 32 mm sealing cap (A)- 7- While expanding the 69 mm snap ring (B) on the countershaft ball bearing with snap ring pliers, lift the transmission housing (C)- 8- Release the snap ring pliers, and remove the transmission housing- 9- Remove the 14 x 20 mm dowel pins (D)- 5.Oil Guide Plate
1- Remove the oil gutter plate (A)- 2- Remove the 52 x 62 mm shim (B)- 3- Remove oil guide plate M- 6.M/T Reverse Shift Fork
1- Remove the reverse shift fork (A)- 7.Reverse Idler Gear
1- Remove the reverse idler gear (A) and the reverse idler gear shaft (B)- 8.Reverse Lock Cam
1- Remove the reverse lock cam (A)- 9.M/T Mainshaft and Countershaft and Shift Fork Assembly
1- Apply a thin layer of tape to the mainshaft splines to protect the seal- NOTE: Do not apply too much tape as it will damage the oil seal- 2- Remove the mainshaft assembly (A) and the countershaft assembly (B) with the shift fork assembly (C) from the clutch housing (D)- 3- Remove the 26 mm washer (E)- 4- Remove the 36 mm spring washer (F)- 10.Differential Assembly
1- Remove the differential assembly (A)- 2- Remove the magnet (B)- Reassembly
NOTE: Prior to reassembly, clean all parts in solvent, dry them, and apply MTF to any contact surfaces- 1.Differential Assembly
1- Install the magnet (A)- NOTE: Clean the magnet any time the transmission is disassembled- 2- Install the differential assembly (B)- 2.M/T Mainshaft and Countershaft and Shift Fork Assembly
1- Install the 36 mm spring washer (A)- NOTE: Be sure to install the spring washer in the direction shown- 2- Install the 26 mm washer (B)- 3- Apply a thin layer of tape to the mainshaft splines (C) to protect the seal- NOTE: Do not apply too much tape as it will damage the oil seal- 4- Install the mainshaft assembly (D) and the countershaft assembly (E) with the shift fork assembly (F), as an assembly- 3.Reverse Lock Cam
1- Install the reverse lock cam (A)- 4.Reverse Idler Gear
1- Install the reverse idler gear (A) and the reverse idler gear shaft (B)- 5.M/T Reverse Shift Fork
1- Install the reverse shift fork (A)- 6.Oil Guide Plate
1- Select the proper size 52 x 62 mm shim (A) according to the measurements made during the Mainshaft Thrust Clearance Adjustment- 2- Install the oil gutter plate (B)- 3- Install oil guide plate M- 4- Install the 52 x 62 mm shim- 7.M/T Transmission Housing Assembly
1- Clean any dirt or oil from the mating surface of the transmission housing and the clutch housing-
2- Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, 08718-0004, or 08718-0009 evenly to the clutch housing mating surface of the transmission housing. Install the component within 5 minutes of applying the liquid gasket- NOTE:
If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes-
If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket-
3- Install the 14 x 20 mm dowel pins (A)- 4- Set the tapered cone ring pawl (B) faces the 5th shift fork (C)- 5- Place the transmission housing on the clutch housing, making sure to line up the shafts- 6- While expanding the 69 mm snap ring (D) on the countershaft ball bearing using snap ring pliers, push the transmission housing down to start the countershaft ball bearing through the snap ring- 7- Release the pliers, and push down the housing until it bottoms out and the snap ring snaps in place in the countershaft ball bearing snap ring groove- NOTE: Install the 32 mm sealing cap (E) after setting in the 69 mm snap ring-
8- Make sure the 69 mm snap ring (A) is securely seated in the groove of the countershaft bearing- Dimension as installed: 3.3 6.5 mm (0.130 0.256 in)
9- Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, 08718-0004, or 08718-0009 evenly to the threads of the 32 mm sealing cap. Install the component within 5 minutes of applying the liquid gasket- NOTE:
If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes-
If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket-
99 Gmc Sonoma Manual Transmission Removal
10- Install the 8 mm flange bolts finger-tight-
11- Tighten the 8 mm flange bolts in a crisscross pattern in several steps- Specified Torque:
8 x 1.25 mm27 N·m (2.8 kgf·m, 20 lbf·ft)
12- Install the drain plug (A) with a new sealing washer (B)- 13- Install the filler plug (C) with a new sealing washer (D) finger-tight-
14- Install the steel balls, the detent ball springs, and the detent bolts (A) with new 12 mm sealing washers (B)- 15- Install the 20 mm bolt (C) with a new 20 mm sealing washer (D)- 8.M/T Output Shaft Speed Sensor
1- Install the output shaft (countershaft) speed sensor (A) with a new O-ring (B) and the plain washer (C)- 9.Back Up Light Switch
1- Install the back-up light switch (A) with a new 18 mm sealing washer (B)- 10.M/T Change Lever Assembly
1- Clean any dirt or oil from the mating surface of the change lever assembly and the transmission housing- 2- Apply liquid gasket, P/N 08717-0004, 08718-0001, 08718-0003, 08718-0004, or 08718-0009 evenly to the transmission housing mating surface of the change lever assembly. Install the component within 5 minutes of applying the liquid gasket- NOTE:
If you apply liquid gasket P/N 08718-0012, the component must be installed within 4 minutes-
If too much time has passed after applying the liquid gasket, remove the old liquid gasket and residue, then reapply new liquid gasket-
2002 Gmc Sonoma Manual
3- Install the 8 x 10 mm dowel pins (A)- 4- Install the change lever assembly (B).
99 Gmc Sonoma Manual Transmission Removal Diagram
Trans/Driveline PCM CVT Control System Circuit Diagram M/T Reverse Lockout Solenoid Disassembly and Reassembly CR-V
Service Manual M/T Reverse Lockout Solenoid Disassembly and Reassembly Removal 1.Air Cleaner Assembly 1- Disconnect the intake air duct (A) and the intake air pipe (B)- 2- Remove the...M/T Countershaft Disassembly, Reassembly, and Inspection CR-V
Service Manual M/T Countershaft Disassembly, Reassembly, and Inspection Special Tools Required ImageDescription/Tool NumberDriver Handle, 40 mm I.D. 07746-0030100Bearing Driver Attachment, 30...